Free NS0-184 Sample Questions — NetApp Certified Storage Installation Engineer, ONTAP

You have just installed an ONTAP 9.8 cluster and created an interface group on each controller. You have also created two VLANs on each interface group. In this scenario, what is the minimum number of broadcast domains that will be created to use the tagged VLANs?

• A. 0
• B. 1
• C. 2
• D. 3

You have a new 2-node FAS8700 ONTAP 9.8 cluster. One of the nodes has 24x16 TB NL-SAS disks assigned and available for a new aggregate. You created the aggregate with one RAID group and two spare disks. In this scenario, how many data drives are in the aggregate?

• A. 20
• B. 18
• C. 17
• D. 19

Which two switch operating system are supported on ONTAP cluster switches? (Choose two.)

• A. Brocade FOS
• B. Cisco NX-OS
• C. Cisco IOS
• D. Broadcom EFOS

You have a 2-node FAS8300 ONTAP 9.8 cluster that serves SMB shares. You are configuring interface groups for higher performance and resiliency. Which two NetApp best practices should you follow to satisfy these performance and resiliency requirements? (Choose two.)

• A. Use ports from different NICs
• B. Use ports from the same NICs
• C. Use ports with different chipsets
• D. Use ports with the same chipsets

You are preparing to add a 2-node AFF A250 system to an existing 4-node AFF A800 cluster with Cisco Nexus 3232C switches. The cluster switches are currently running the Cluster-HA RCF. In this scenario, which two steps are required to install the AFF A250 system? (Choose two.)

• A. Load the Storage RCF
• B. Cable the AFF A250 nodes to the next free ports on the switch
• C. Cable the AFF A250 nodes to the breakout ports on the switch
• D. Load the Cluster-HA-Breakout RCF

You are installing an AFF A700 system with two disk shelves using ADPv2. After setting up the cluster, you realize that one drive shelf was powered off and that the drives have not been assigned to any of the nodes. In this scenario, which two resources will help you find a solution? (Choose two.)

• A. Active IQ Config Advisor
• B. NetApp Documentation Center
• C. NetApp Knowledge Base
• D. Active IQ Digital Advisor

You must install a new FAS500f system at a customer's site. You are preparing for the installation and realize that there is no console cable to connect to the controllers. In this scenario, which type of cable do you need to complete the installation?

• A. a DB9-to-USB cable connected to the DB9 port of the controller
• B. a micro-USB-to-USB cable connected to the micro-USB port of the controller
• C. an RJ45-to-DB9 cable connected to the RJ45 wrench port of the controller
• D. a USB-to-USB cable connected to the USB port of the controller

When creating a new 3.8 TB SSD-based aggregate, what is the default RAID type used with ONTAP 9.8?

• A. RAID 4
• B. RAID-TEC
• C. RAID 0
• D. RAID DP

Your customer plans to expand a 2-node FAS2750 switched cluster with two new controllers. In this scenario, which two prerequisites should you examine in advance? (Choose two.)

• A. Verify that the hard drives of the new controllers are compatible with the old controllers
• B. Verify that the existing cluster has a minimum 10 GB of free space for root volumes
• C. Verify that the existing switches support the additional controllers
• D. Verify that the platform of the new controllers can be mixed with the cluster’s existing controllers

After moving a new AFF A400 cluster into production, the administrator notices error events in ONTAP System Manager regarding SAS HA issues. In this scenario, which NetApp tool would have identified these errors after the installation process?

• A. Cloud Manager
• B. ONTAP System Manager
• C. Active IQ Config Advisor
• D. Active IQ Unified Manager

You are installing a new six-node ONTAP 9.8 cluster. You have completed the initial configuration of the cluster interconnect switches and the ONTAP cluster. In this scenario, which feature should you enable?

• A. cluster switch logging
• B. cluster switch health monitor
• C. IPv6 on all cluster ports
• D. data center bridging protocol

After adding two nodes to an FC-enabled cluster, the storage administrator wants to ensure that existing LUNs can use paths on the new nodes. What is required to complete this task?

• A. Use the storage port rescan command
• B. Use the lun mapping add-reporting-nodes command
• C. Use the lun bind create command
• D. Rescan the bus on the hosts by using the rescan-scsi-bus.sh script

After the Installation of a new NetApp FAS system, you use theNetAppDocs tool for site design documentation. In this scenario, in which three document formats would you create an inventory report? (Choose three.)

• A. docx
• B. html
• C. pdf
• D. ps
• E. xlsx

You are deploying an 8-node AFF A700 by using BES-53248 cluster switches. During the installation, you notice that ports higher than 16 are not coming online. You verify that the additional licenses are installed. Which two additional steps must be taken to bring the additional ports online? (Choose two.)

• A. Reload the firmware
• B. Reload the RCF file
• C. Re-enable each port
• D. Reload the switch

Which two statements are true about the LIFs that are used for a cluster peer relationship? (Choose two.)

• A. The MTU size must be set to 9000 bytes on all the LIFs used for the cluster peering
• B. The LIFs must use the default intercluster service policy
• C. The LIFs must be in dedicated broadcast domains an IPspaces
• D. At least one LIF per node is required on each cluster